Godox and Cheetahstand users- Problem solved

dmward wrote in post #18041649
That's nice. TTL, with a bare bulb, speedlite size, and the Li-Ion battery.

Sounds IDEAL !!!

abbadon31 wrote in post #18041790
I'm sure everyone will be selling them Adorama / Cheetahstand / Amazon / Ebay / B&H

LOL I thought that about the 850ii

hello, i have one question, i have ad360 with ft16 triger (433mhz), now i want to byu AD600 ttl, with triger X1TC , question is:
can i put my old ft16 on hotshoe of X1TC and work with both flashes AD600 and Ad360,one ttl second manual?
THX

This has bee answered before. Godox produced the XTR-16 which has the same function but communicating directly with the X1TC and you can put the FT-16 to rest. Please take batteries out of the FT-16 so that they won't leak in time, inside the FT-16 transmitter.

mmmfotografie wrote in post #18048839
This has bee answered before. Godox produced the XTR-16 which has the same function but communicating directly with the X1TC and you can put the FT-16 to rest. Please take batteries out of the FT-16 so that they won't leak in time, inside the FT-16 transmitter.

The XTR16 /XTR16s don't function right and can be a pain in the ass. If I want to use the version one units, I use the old receivers and use the old transmitter in the hotshoe of the x-1. I find the old 433Hz more reliable then the new 2.4Ghz for the older units.

I have still that problem locking up with the AD600 and FTR16 and the XTR16 did not get locked by the AD600 till now. Using a XT32c as trigger.

Update 26 June: just tried out a test run with the XTR16 receiver attached to the AD600 and triggered by the XT32c and I could not lock up the receiver and it did not miss a flash. It seems to be only the two FTR16 (433MHz) that are locking up on the AD600.

me too big problem, my X1Tc work great with AD600, but with ad360+xtr16 is a big problem, only can flash on full power (cant change a power), i also used old reciever ftr16 + attached ft transmiter on x1tc and workink good...

I suspect your XTR16 may be defective.

DejanNikolic wrote in post #18059237
me too big problem, my X1Tc work great with AD600, but with ad360+xtr16 is a big problem, only can flash on full power (cant change a power), i also used old reciever ftr16 + attached ft transmiter on x1tc and workink good...

Sounds like you have it in the wrong group.

You can only use A/B/C/D/E

Hi again.

I believe you've posted about this issue in more than one thread, so it's a bit tough to keep track of everything you've tried.

In another thread, in response to questions about your Group settings, you wrote:

This does not make it clear whether you have set the group to A on both transmitter and XTR16.
Have you?

As David wrote in another thread:

The wheel sets the group. Gr A on the X1T requires that the wheel on the XTR-16 is set to A.


It might help if you could include, in one post:

- Model numbers and firmware versions of the hardware being used
- channel setting of transmitter
- group setting of transmitter
- channel setting of receiver (dip switch pattern on XTR16)
- group setting of receiver (wheel on the XTR16)

Owen.

thx for reply,
model number of x1t is v15
chanel is set to 1, gr is A on transmiter
reciever is set 1 and group is A,
camera 5Ds canon, + ad360 + x1tc

DejanNikolic wrote in post #18062904
thx for reply,
model number of x1t is v15
chanel is set to 1, gr is A on transmiter
reciever is set 1 and group is A,
camera 5Ds canon, + ad360 + x1tc

The "receiver" described is the XTR-16, right?

So, the wheel on your Xtr-16 is set to A, and all four of its little switches are in the "down" position, (this is channel 1), correct?

If so, I would also try setting the XTR-16's wheel to "B" and to "9" just in case your particular XTR-16's manufacturing was a bit "off".

Assuming that doesn't work, I would suggest you try to find another XTR-16 to test.

You could also update the firmware of your X1T-C, but I don't think that is likely causing the problem.

Owen.

this video best describe my problem...

https://www.youtube.co​m …sItt0o28&featur​e=youtu.be

DejanNikolic wrote in post #18065011
this video best describe my problem...

https://www.youtube.co​m …sItt0o28&featur​e=youtu.be

I have the xtr-16 in the video from Jimmy and Cheetahstand sent him a new one. I tested and tested it and it works just fine with my setups. Not sure why it was not working for him and he got a replacement and then returned all his stuff back for a refund.

When using the Godox 360II in wireless radio slave mode "off camera", the Godox 360II will continue to flash the two optical slave LED's. VERY annoying to the person in front of the flash! Is there any way to turn this off?